Cleaning Gas, Diesel or Furnace Oil on Water

1. Blend Micro 50^TM with warm water 3:1 (Water:Micro50^TM)
2. Spray on rainbow floating on water
3. Notice rainbow immediately disappears

Cleaning Grease & Fuel Grime on Equipment i.e: Fuel Pumps, Tractors, Farm Equipment etc.

1. Blend Micro 50^TM 9:1 with warm water
2. Spray on equipment you wish to clean grease from using either a pressure sprayer or a foaming gun (note that foaming guns will permit much higher water to Micro 50^TM ratios)
3. For smaller parts washing, mix one part Micro 50^TM with 4 parts water and spray or pour on. Use a brush or rag appropriate for the type of part(s) being cleaned to loosen and remove grease/grime buildup. Alternatively, use Micro 50^TM in parts washers as an alternative to caustic and dangerous solvents.
4. Rinse with water after letting stand for 30 seconds

Cleaning Parts with Micro 50^TM in a Parts Washer

Micro 50^TM makes for a safe and effective alternative to harmful and caustic solvents in a partswasher application. It's powerful surfactant effectively breaks down and removes grease and grime from the parts, and it's 50 billion microbes per litre actively digest the hydrocarbons in the solution.

1. Dilute 1 part Micro 50^TM to between 2 & 4 parts water depending on the level of aggression you require from the solution.
2. The cleaner’s rinse fountain will circulate the Micro 50^TM solution while it’s in use, but adding an air pump (as used in fish tanks) is recommended to ensure the microbes have a constant air supply as they consume the hydrocarbons.
3. Clean the parts using the cleaner’s brush and other stiff-bristled brushes. For heavy, dried on grease it may be necessary to let the part soak prior to scrubbing.
4. When clean, wipe the part with a dry rag and blow out any holes that may still contain the solution.

Cleaning motor oil stains on concrete

1. Blend 4 parts warm water (preferable) with 1 part Micro 50^TM (4:1) for heavy or aged stains. Use up to a 9:1 ratio for light stains
2. Spray or pour on stain on concrete
3. Because motor oil stains have dirt on the surface of the stain, use a highly diluted (9:1) mix of water and Micro 50^TM with a rag first to clean the surface of the stain. You will notice it seems like mud and a smear will appear on the concrete
4. Wash concrete until smear is gone
5. Re-apply blend of Micro 50^TM to concrete surface
6. Scrub with a stiff-bristled brush or broom
7. Wash with power washer or hose if possible after at least one hour or let sit indefinitely

Note that motor oil stains are quite muddy and require some effort to remove and will not disappear like lighter hydrocarbons will.

Cleaning Soot from oil furnace in carpet or fabric:

1. Blend Micro 50^TM 5:1 with warm water
2. Spray on carpet and work around with wet cloth
3. Once black marks are reduced to slight darkened area on carpet, squeeze water out of clean sponge onto carpet and reabsorb from carpet and all black stain will be lifted from the material. Rinse sponse and repeat until completely clean.

Cleaning Soot from oil furnace on concrete:

1. Blend Micro 50^TM 5:1 with warm water
2. Spray onto concrete area effected by stain
3. Work area with brush
4. Wash out with water until clean

Cleaning Furnace oil, diesel and gasoline stains and spills in concrete, asphalt, brick, siding etc.

1. Blend Micro 50^TM 4:1 with warm water
2. Spray on surface and scrub with brush/broom till lather develops
3. Let sit indefinitely if in someone's house ie: basement and the stain will go away over time
4. Power wash or wash with hose if outside after letting sit for at least one hour

Cleaning Furnace oil in the ground and on grass:

1. Blend Micro 50^TM 3:1 with warm water – use equal volume of concentrate to spill
2. Pour mixture on ground
3. Let sit indefinitely

Cleaning Fuel & Oil Buildup From Bilges

1. Blend Micro 50^TM with warm water (if available) 5:1 (Water:Micro50^TM)
2. Pour mixture into hand sprayer or pressure sprayer
3. Liberally soak the affected areas of the bilge, scrubbing the heavily contaminated areas
4. Notice the Micro^TM immediately breaking down the oil and fuel build up
5. Allow the Micro^TM solution to splash around in bilge area. If dry the wipe with rag.